J Downs Plumbing LLC
Your Cart is Empty
There was an error with PayPalClick here to try again
Thank you for your business!You should be receiving an order confirmation from Paypal shortly.Exit Shopping Cart
|Posted on May 26, 2012 at 10:57 AM||comments (3)|
Replacing the Flapper
Replacing the flapper is generally an easy fix and may be replaced when you experience a leaky toilet. Like in part one, be sure that the incoming water supply to the toilet tank is turned off. Remove the tank lid and as stated in part one and put it in a safe place. Hold down the tank lever and let the water exit the tank. At this point, you may wish to use a pair of disposable gloves to protect your hands. Generally, the flapper will have a film covering it from being exposed to the chlorine in the water. The film will stain your hands as well as your clothing!
Next, remove the chain from the tank lever and remove the flapper. There are a variety of types and styles of flappers available. You’ll need to take your existing flapper with your to your local hardware, plumbing supply, or home improvement center. In most cases, they should be able to provide either an exact, or an adequate replacement.
When you get back home, simply connect the flapper back into place and connect the chain and you are done!
Replacing the Fill Valve:
The replacement of the toilet’s fill valve is generally an easy task. The first step in the process is to secure the incoming water to the toilet tank. Once this is done, remove the tank lid, and put it in a safe place. Tank lids vary by manufacture and can prove to be costly when they are broken! Now, hold the tank lever down and open the flapper letting as much water exit the tank as possible.
Once the toilet tank has drained, remove the excess water with a sponge or shop-vac until the tank is dry. Next, remove the supply line from the fill valve. After the supply line is removed, remove the shank nut from the fill valve. Now you should be able to remove the fill valve from the tank.
There are a variety of different fill valves available. As a rule of thumb, take the fill valve you are replacing with you to your local hardware or home improvement center. An assistant should be able to provide you with an adequate replacement.
|Posted on March 11, 2012 at 10:33 PM||comments (11)|
Are you interested in learning how to not get ripped off by plumbing services, or from any other contractor for things like furnace repair, heating repair, or anything else?
This article will help you to find out if your plumber or contractor is ripping you off, and what you can do to stop it. This advice was written to help stop others from overpaying the next time they need plumbing repair, but can be used for any kind of contractor.
Follow these steps to ensure that you’re getting the most out of your plumber:
Making a Plumber your Own
Plumbing services are one of those things that you usually only need in emergencies. When your sink or tub starts leaking, or you find yourself swimming in your bathroom from an overflowing toilet, you’ll often call the first plumber that you find.
Doing this can result in overpaying for poor plumbing repairs that can cause bigger problems down the road. A plumber may install a fix that only temporarily relieves you of an issue, but it only worsens the fix that you will need down the road.
The first thing you need to do is to find out the plumbing services that are available in your area. You can use a phone book to do this, but the Internet is often a better option and will give you more information.
Make a list of five plumbers that you would think about using and begin finding out more about them.
Call the plumbing company and ask them some basic and necessary questions:
Additionally, you can often find customer testimonials on company websites. There are also services like Yelp and Citysearch that offer customer reviews that you can check to find out about the types of experiences that others have had with the service.
Eliminate Emergency Repairs
After finding a plumbing service that you are satisfied with, you should use them to do a preventative checkup to make sure that there are no major plumbing issues lingering around the corner. Routine maintenance can save you from headaches and enormous plumbing repair bills by stopping a problem before it even starts.
Preventative maintenance is often very cheap and will reduce your future plumbing concerns. It will also give you an opportunity to find out more about your plumber by meeting their technicians and finding out if their services are as advertised.
Share What You Now Know
Help others with the difficult decision of choosing a plumber by sharing the information you’ve gathered.
Submit your testimonial to companies so that they can put it on their website for others to see. You can also publish your review on websites like Yelp and Citysearch so that others will know more about the company and the kind of experience you had.
There is no point in not sharing your experience and it only takes a few moments to publish a helpful review that will lead others to a reliable and trustworthy plumbing company.
By letting others know about the information you have accumulated or the experience you had, you will save them from getting taken advantage of during their own plumbing emergencies.
The best ways to get the most out of your plumbing services and avoid getting ripped off is to make sure that you are adequately prepared beforehand. Find a reliable plumber in your area through research, allow them to perform routine maintenance, and then help others by sharing your information. This advice also works for furnace repair, heating repair, and any other kind of service where you are using a contractor.
We have all heard this sound before in our bathrooms… drop, drop, drop, drop. There is nothing more annoying than listening to water drip from the height of that shower faucet. The first step in fixing this problem is to find exactly where the water is dripping.Is it the showerhead? Or is it one of the knobs? This article discusses how to repair and replace a showerhead.Why Is My Showerhead Leaking?Most of the time, you showerhead needs replacing due to the much water pressure that it endures over the many years of use. Additionally, poor maintenance could result to a shower faucet head leaking. Sometimes, your showerhead might need some tightening.If you are using an older showerhead, you might want to consider purchasing a new and modified showerhead. The reason being is that these new showerheads are redesigned and reengineered to control the water flow – conserving water and being energy efficient.Keep this in mind: all of this new shower technology is inexpensive. You can get an energy efficient showerhead for less that $10 – for the more pricey ones – expect to pay no more than $100. Just think that you could be saving anywhere from $7 to $10 a month on your water bill, just by switching to an energy efficient showerhead.Replacing The ShowerheadBefore purchasing a showerhead, always check if you need to tighten your current showerhead – sometime this might be a simple fix. Just check to see if it’s loose. If so, then just skip to the next paragraph to see how you can tighten your showerhead. If your showerhead is firmly connected to the water line, then it is best to purchase a new one.Simply unscrew the old head for the water supply. Most showerheads can actually be unscrewed by hand, but if won’t move use a Crescent wrench. Make sure you turn the wrench slowly! You don’t want the water supply line to break while unscrewing the showerhead.The new showerhead will just screw back on the same way. Before installing the new showerhead – to better ensure that your faucet won’t leak again, make sure you put some PTFE tape on the threads of the water supply line. This will close all of those small gaps and ensure that you won’t hear that annoying sound ever again.Enjoy your being environmentally friendly and happy showering!
You may have toilet flange repair in your future if you sit down on your toilet and feel like you just sat down a rocking horse. When the toilet flange wears out, your toilet will often become unstable and seem to see-saw back and forth. Another thing that commonly happens when you need to repair or replace your toilet flange is leaking from the bottom of the toilet. The floor around your toilet may always be wet (but don’t let condensation fool you… that can also cause the floor area around your toilet to be wet).If you rule out condensation and identify that there’s a leak coming from the base of the toilet, then it’s time to get ready for some toilet flange repair. First you should shut off the water. You can do this either locally at the shut off in your bathroom or you can simply shut the main water supply off to the house. You’ll probably want to have a helping hand around in order to lift the toilet up and getting it set aside. Take the bolts out and move the toilet so you can get to the flange.Once the toilet is out of way, you’ll see a wax ring that is connected to a horn-shaped metal piece. That is your flange. If it isn’t perfectly even, both vertically and horizontally, it won’t fit perfectly to the toilet and will give you a rocking chair of sorts for a toilet. There are special toilet flange extenders you can buy if it’s too low to properly seat.Look at the flange and see if it’s worn away in any area or if is rusting. If there is no sign of damage, you could simply need a new wax ring. If that’s the case, remove the old one with a putty knife. Ensure you leave a smooth, clean and level area for the new ring. Put your new one on, replace the toilet and put the bolts back in.In a worst-case scenario, your flange may have become ruined (you’ll need to replace it) and your floor may be damaged. This can happen from tightening the flange nuts to tightly or from the floor being uneven to begin with. You can get support brackets that will shift weight to good parts of your floor. Of course, if the floor has been damaged extensively, you’re looking at major repairs. If you aren’t sure if the flange needs repaired or simply replaced, a plumber can easily help you out. Often times, you’ll be able to see any obvious damage and know immediately that toilet flange repair or replacement is what’s needed.
running toilet can simply drive you up the wall but you may not be sure how to repair a running toilet. In reality, it isn’t always as big of a task as you may think it is. Learn about toilet repair in this article on running toilet repair. If you’re hearing the water in your toilet run constantly or it seems to just turn on and off whenever it wants, you can usually figure out what’s going on with a little investigation. The good part is that your local hardware store or home store likely carries everything you need to repair your running toilet.The flap inside your toilet could be stuck open, which is causing the water to run. Take the top of the back of your toilet and look to see if the little flap inside is seated and sealed or if it’s stuck open. The flapper is a little rubber gasket that sits in the bottom your tank. It will have a lever or a chain that is connected to it, which connects it to the toilet handle in most cases. If it’s open then just slide your hand in there and adjust it so it seals properly. That could easily be the only thing you need to do to repair your running toilet. The flap is made of rubber or another soft material that is prone to damage and dry-rotting over time. If it looks like it’s been damaged, you should replace it. Once it gets too damaged, it won’t matter how much you try to get it to seal. Water will slip past it and leak through, leaving you with a constantly running toilet and higher water bills.If it’s sealed properly, check the chain while you’re in there. Is it twisted, bunched up or caught on anything? If so, it probably isn’t letting the flapper seal right. Straighten it out and see if that helps. You will also see a rod. Is it bent? Again, if it is, you should be able to straighten it out pretty easily. If you notice it’s getting rusty or anything, you should go ahead and replace it.In the tank you should also see a little ball-looking thing. That’s your float mechanism. Lift it up and see if the toilet stops running. If it does then you found you problem. Adjust the arm and let it go. Keep adjusting it a little bit and see if you can find a point at which the toilet stops running. If you happen to find that there is water inside the ball, you’ll need to get a new one from your local hardware or home store.If none of the above seems to help, you may have a larger leak that is a little more troublesome. A professional plumber will be able to determine exactly what’s causing the leak and repair you running toilet for you.
Every home owner comes to a day when they have to learn a thing or two about toilet bowl repair or they have to pay a professional plumber to come in and handle the problem. Even if you don’t own a home, it’s nice to know some basics about toilet bowl repair so you don’t have to call your landlord for every little problem that comes up in the bathroom. Toilet bowls have many ways that they can start to go haywire and for several reasons. It’s just a fact of life. How many times have you visited someone and they tell you “Jiggle the handle when you’re done!”?One of the most common reasons you’ll need to know a little about toilet bowl repair is a clogged toilet. Sure, it can happen because someone put something or too much of something into the toilet and tries to flush. But a stopped up toilet, or even one that doesn’t seem to fully flush, can both be caused by something clogging your pipe. If you’ve plunged to no avail, then see if you can get your hands on what’s called a “snake”. This is a tool that you can run down the pipe and hopefully clear any clogs. If not, then you may need to throw in the towel and call in a professional for your toilet bowl repair this time.Another problem that you’re likely to face is a leaky toilet. Sometimes they can be pretty simple to handle if it’s easily identifiable. Toilets can seem to leak simply from condensation. So before you go investing in tools, parts, equipment or paying a plumber, keep an eye on the outside of your toilet bowl and see if you notice a build-up of condensation. It can drip onto the floor and make it look like you have a leak when you really don’t. If condensation doesn’t appear to be the issue, then you’ll have to figure out where the leak is coming from. Is it dripping from the flush handle? Is it leaking from the area where the pipe connects with toilet? Is water coming out from under the base of the toilet? Depending on where the leak is coming from and your confidence level you may be able to fix it or you may need to call a plumber.If your toilet is constantly running, this is a toilet bowl repair that you can probably fix. Simply remove the lid from the back of your toilet. There’s a hole that should be snugly sealed once the toilet flushed. If you watch in there as you flush, you’ll see where it opens up. Inspect that area and ensure that it is sealing properly. If it’s not, look at the pieces and see if any of them are bent or rusted. If you can spot where the problem is, take that part to your local hardware store and ask them for a replacement part. Before removing the part or replacing it, turn the water supply to your toilet off.
If your bathtub faucet is leaking, you should get it repaired as soon as possible. If you don’t take care of your bathtub faucet repair in a timely manner, you will waste a ton of water, pay much more on your water bill than you have to, and possibly end up with rusty parts that you’ll have to replace. If your bathtub is relentlessly dripping, you don’t necessarily have to pay a plumber to come in and fix it for you. There are some things you can do first to see if you are able to remedy the situation. It’s cheaper to do it yourself, but if you can’t get it to stop, then you’ll obviously need the help of someone who knows what they are doing.There are two common leaks that will require bathtub faucet repair. Chances are that your faucet is leaking from the base when you turn the water on or there is a constant leak that drips from the faucet, even when the water is turned off. Good news is that both of these leaky headaches can often be corrected with the same solution.The first thing you need to do is turn off your water supply. You’ll probably find a shut off valve hiding under your bathroom sink or in the vicinity of the sink. If you can’t find it, you can just turn off the main water supply to your house. Also, make sure the water supply to your water heater is cut off. After turning off the water supply, wait a few minutes before you begin your bathtub faucet repair.If your faucet handles have a decorative front, you’ll probably need to remove them. They should just snap on and off. Take a thin washcloth or some kind of other soft cloth and cover the tip of a flat-head screwdriver. You can use that to pry off the decorative front. Remove the screw from the center of the handle if there is one. Now you should see a nut underneath there. Loosen and remove it, then take out the rod-like piece.Clean out the inside of the cavity while you’re in there. Clean the rod-like piece with a soft cloth and a mild soap that isn’t too abrasive or harsh. If it’s covered in rust, corroded, or simply worn down, you’ll need to replace it. Take it to a hardware store so they can help you get the right replacement part. As for the washer, it’s best if you just replace it while you’re in the process of repairing your bathtub faucet. Even if it appears to be in pretty good shape, take out the screw and go ahead and replace the washer. You can normally find a generic washer with the same width and diameter that will work perfectly.Put the new washer on and put the screw back in. Insert your rod-like piece back into place within the cavity you took it out of and turn it clockwise. Don’t try to make it too tight, as you could strip the threads. Put the handle back on and put the screw back in. Snap your decorative cap back on if you had one. Test it out! Your bathtub faucet repair should be completed now. Special tip: Wrap the threads on your rod-like piece with Teflon tape while you have it out. This will help keep the handle from leaking.Need plumbing repair? Get estimates from plumbers in your area.
Faucet leak repair begins with knowing what kind of faucet you have and the most common reasons why they fail in the first place. We’ve all been there… in the middle of night listening to the drip-drip-drip of a leaky faucet tapping in the sink. It’s more than just something that drives you up the wall. It can shoot your water bill up, which is something no one needs these days. Plus, left untreated, you could end up with corroded sink bowls and fixtures.Before you even begin thinking about getting into faucet leak repair fixing your leaky faucet, you will need to know what kind of faucet you have and the different parts that commonly go wrong in each one. Faucets generally come in one of four basic types: cartridge, compression, ball and disc. It isn’t as difficult as it sounds to know what kind of faucet you are dealing with, though.Many newer homes have a single handle that lets you control the cold and hot water. If you have this kind of faucet, then you have either a disc, ball, or cartridge faucet on your hands. If you have the traditional faucet that has two handles, one for the cold water and one for the hot, then you probably have a compression faucet. Two-handle faucets can also sometimes be a disc faucet too.A leaky faucet is usually due to seals, o-rings, and washers that need replaced. If your seals or washers need replaced, you can count on your faucet dripping. If your faucet is leaking around the handle, you can usually handle this faucet leak repair by simply removing the handle. Check the o-rings that are found on the stem and see if they’re worn. You can also try tightening or adjusting the packing nut and adjusting ring to see if that solves the problem.On a compression faucet, the seals and washers are constantly being pressured into the metal valve seats. For this reason, these faucets are bound to start dripping at one point or another. These washers aren’t found in the cartridge, ball and disc faucets. They are much more likely to drip from the base of the faucet than from the spout.The worst thing you can do if you need to repair a leaky faucet is to ignore it (this will only make future a future faucet leak repair more costly). The second worst thing to do is to keep trying to tighten down the faucet, as you’re likely to torque it too much and permanently damage the faucet. If you can’t seem to find the parts that need replacing, then you may need to get some help from a professional plumber.